Engine Peak Performance, Suspension Mastery, Transmission Restoration
Axiview delivers specialist automotive repair across three focused service divisions. Whether your engine needs precision tuning, your chassis demands alignment and suspension work, or your transmission requires expert rebuilding, our technicians diagnose and resolve the root cause—not just symptoms.
Torque & Tune Workshop | Engine Performance Tuning at Axiview
Is your engine performing at its actual potential, or are you leaving horsepower on the table? Torque & Tune Workshop extracts hidden power from your engine through strategic calibration, fuel mapping adjustments, and load optimization—proven methods that increase both output and drivability without compromise.
- Dyno-Verified Power Gains — Every tune exits our workshop with documented horsepower and torque numbers. You see the before-and-after results on our dyno printout.
- Engine-Specific Calibration Logic — A tune that works for one engine variant may create drivability issues in another. We map your exact vehicle specifications for precision results.
- Reliability Monitoring Built In — Aggressive tuning without safeguards leads to premature wear. Our calibrations include knock detection thresholds and cylinder protection protocols.
- Fuel Mapping Adjustments — Strategic fuel delivery recalibration for improved combustion efficiency and power output across all RPM ranges.
- Load Optimization — Tuning tailored to real-world driving loads, not just peak performance figures.
- Post-Tune Road Validation — Every tuned vehicle is verified on road conditions before handover to the owner.
Chassis Care Masters | Professional Suspension & Steering Service in Malaysia
Your chassis absorbs punishment every time you hit a pothole, brake hard, or navigate rough urban streets. Poor suspension geometry and misaligned steering don't just affect comfort—they accelerate tire wear, reduce braking efficiency, and compromise your safety in emergency situations. Chassis Care Masters restores your vehicle's handling precision from the ground up.
- Laser-Precision Alignment Technology — We don't estimate angles—we measure them. Our 3D alignment system captures wheel geometry to 0.1mm tolerance.
- Suspension Rebuild Without Guesswork — Worn struts, damaged bushings, and fatigued springs don't always announce themselves with noise. We perform physical component inspection.
- Steering Response Restoration — Heavy steering, delayed response, or a wandering feel indicates tie-rod wear, ball joint play, or rack-and-pinion issues we resolve at the source.
- Full Chassis Geometry Assessment — Comprehensive multi-point inspection of all suspension and steering components before and after service.
- Pothole & Impact Damage Diagnosis — Targeted assessment of chassis impact damage from Malaysia's urban and highway road conditions.
- Tire Wear Pattern Analysis — Alignment-related tire wear identified and corrected to extend tire service life and restore even contact.
Workshop Hours & Contact
| Day | Hours | Contact |
|---|---|---|
| Monday – Friday | 8:00 AM – 6:00 PM | +60 3 2145 7832 |
| Saturday | 8:00 AM – 2:00 PM | contact@axiviewe.xyz |
| Sunday | Closed | 114 Jalan Tun Sambanthan, Kuala Lumpur 50470, Malaysia |
Transmission Revival Centre | Axiview Auto Service Malaysia
Manual or automatic, CVT or dual-clutch—transmission faults demand precision repair, not guesswork. Axiview's Transmission Revival Centre combines diagnostic scanning with hands-on rebuild expertise to diagnose slip, lag, and noise at their source. We inspect seals, measure clearances, and replace worn components to factory specification.
- Transmission Pull & Inspection Protocol — Rather than guessing based on symptoms, we remove and bench-test the gearbox. This reveals worn bearings and scored clutch packs directly.
- Fluid Flush & Pressure Verification — Old transmission fluid carries metal particles and sludge that accelerate wear. We drain contaminated fluid and replace filters and seals.
- Dyno Post-Repair Testing — After rebuild, your transmission runs on our dynamometer to confirm shift points, engage smoothness, and torque delivery accuracy.
- CVT & Dual-Clutch Specialisation — Expertise across all transmission types including modern CVT and dual-clutch configurations common in Malaysian-market vehicles.
- Seal & Clearance Measurement — Precision measurement of internal clearances and replacement of all worn seals to prevent post-repair leaks.
- Shift Calibration & Programming — Electronic recalibration of transmission control modules after mechanical rebuild for seamless gear engagement.